Jump to content

Xtreamer e-Trayz 2 bay NAS


coderunner

Recommended Posts

coderunner

Hello,

 

I'm looking for de setup (install software)  cd for Xtreamer e-trayz (photo below downloaded from the internet)

Does anybody have the cd and can make an iso  of the cd and upload it because mine has an unrecoverable crash on it so I can't use it anymore.

The software isn't on internet anymore.

 

Thanks in advance.

Best regards.

 

1791581_1.jpg

Link to comment
Share on other sites


  • Replies 8
  • Views 1.7k
  • Created
  • Last Reply
ROADKILLER

I have 5 versions Xtreamer e-Trayz to choose from: 1.0.0, 1.0.3, 1.0.4, 1.0.5, 1.0.7.

Which version are you interested in? I think it will depend on the firmware version 🙂

Link to comment
Share on other sites


coderunner
Spoiler

 

 

I think the latest version, if it's possible of course.
I have a feeling my NAS is broken <_< 

Blue light stays on and hard disks don't do anything.

Even it doesn't get an IP

 

 

Link to comment
Share on other sites


coderunner

My NAS doesn't find an IP and the hard disks don't do anything anymore … :(

-> Broken NAS -> garbage ...

 

Link to comment
Share on other sites


ROADKILLER

Trouble Shooting from Xtreamer Support System
 

Quote

1) In case Xtreamer e-TRAYz cannot be accessed via Network
• Check network status and if network port is correctly connected.
• Check if access to Xtreamer e-TRAYz is blocked by firewall, etc.
• In case IP is not known, refer to 2) below.
• In case network setup is incorrect, refer to 3) below.
• If not falling within the previous points of 2) and 3) below, check for abnormalities in LED operation by checking LED status at the front of equipment.
• Request technical support if LED does not operate normally.
2) In case access is not possible due to forgetting IP address of Xtreamer e-TRAYz.
• A WindowsXp or higher comes with a function to find a UPnP device in the network environment. If the UPnP is not active, activate it.
• The name of this device is searched automatically.
• Click this device and the web browser will start, getting the web page of this device. You can get the IP address from the address of the web page.
3) In case access to Xtreamer e-TRAYz is not possible at all due to incorrect network setup
• Click Reset button on the rear of device until the single beeping
• The network initialization is completed with 2 beeps.
• For the initialized network IP, refer to the section of network setting in manual.

4) Does not recognize Hard Disk(not turned off the RED LED)
• Make sure that the Hard disk is mounted the exact location.
• Please fix the HDD

 

Link to comment
Share on other sites


coderunner

Thank you very much ROADKILLER for looking up for a solution for the Xtreamer. I sure going to do this all but I have a feeling it's broken.
When hard disks are in the Xtreamer and turn it on I don't even get a beep or a blue or red light.

When I remove the hard disks a blue light flikkers but that's all.

When I do a full reset on the rear of device I don't get any beeping sound at all so ….

 

But as I said … I will do it back as described in your post here above.

 

Thanks again … cross your fingers … :mellow:

 

 

Link to comment
Share on other sites


coderunner

Did all what you wrote and found out that nothing works so NAS is good for the garbage … even the 2 hard disks are dead so probably a short circuit in the Xtreamer.

Too bad but ...

 

Regards

Link to comment
Share on other sites


Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...